Basic electronics components list ( 55 ) :
Transistors
- 2N2222
- General purpose Si-NPN transistor 60..75V 0.8A 0.5W 250MHz B>100
- 2N3055
- general purpose power transistor 100V/15A/115W, old type in TO-3 metal
case, still useful in linear power supplies
- 2N3904
- General purpose Si-NPN 60V 0.1A 0.625W 250MHz B>100 TO-92 plastic
case, look at
- 2N3905
General purpose Si-PNP 40V 0.2A 0.625W 200MHz B>100, TO-92 plastic
case, look at
- 2N3906
- General purpose Si-PNP transistor
- BC327
- General purpose Si-PNP transistor 50V 0.8A 0.625W 100MHz TO-92 plastic
case
- BC337
- General purpose Si-NPN transistor 50V 0.8A 0.625W 100MHz TO-92 plastic
case
- BC547
- General purpose Si-NPN transistor 50V 0.1A 0.5W 300MHz TO-92 plastic
case
- BC557
- General purpose Si-PNP transistor 50V 0.1A 0.5W 150MHz TO-92 plastic
case
- MJ2955
- Complementary Silicon PNP Power Transistor 15A/60V/115W
-
TIP31
NPN Epitaxial Silicon Power Transistor
- TIP41C
Power transistor in TO220 case NPN 6A 100V
FET
- 2N3819
- N-channel JFET (soon to be obsolete), small signal, 25V 10mA 350 mW
400 MHz TO-92
- BF245
- BF245A
- N-channel symmetrical junction field-effect transistor 700 MHz,
interchangeability of drain and source connections, suitable for LF, HF and
DC amplifiers, TO-92 variant package
- BS170
N-Channel enhancement mode field effect transistor for low voltage, low
current applications (up to 500 mA)
Diodes
- 1N4007
rectifier diode 1A 1000V
- 1N4148
General purpose silicon diode 0.2A 75V, High Conductance Fast Diode
Opamps
- RC5532A
Low noise dual operational amplifier - This is a very good for many
audio designs. The 5532 has THD down around 0.0003% at normal levels and
frequencies. The self noise is no worse than a 10 k ohm resistor. Read also
- LM741
- general purpose operational amplifier, also known as
-
LM324
Low Power Quad Operational Amplifier - check alse
-
LM358
- LM358
Low Power Dual Operational Amplifier
- LM380
- 2.5W Audio Power Amplifier IC for consumer applications. Amplifier
gain is internally fixed at 34 dB. Input stage allows ground referenced
input signals and utput automatically self-centers to one-half the supply
voltage. The output is short circuit proof with internal thermal limiting.
- LM386
Low Voltage Audio Power Amplifier. The LM386 is a power amplifier
designed for use in low voltage consumer applications. The gain is
internally set to 20 to keep external part count low. This amplifier IC can
drive 8 ohms speaker nicely with maximum power from 250 mW to 1W depending
on operating voltage and IC version. Typical operating voltage range is
6-12V.
- NE/SA/SE5532/5532A
Internally-compensated dual low noise operational amplifier
- TL072
Low noise dual operational amplifier
- TL082
Regulator ICs
- KA7805
- 3-Terminal 1A Positive Voltage Regulator for 5V output voltage
- LM78xx
series positive voltage regulators - up to 1A regulator at constant
voltages (7805=+5V, 7808=+8V, 7812=+12V, 7815=+15V, 7818=+18V), includes
overcurrent and therminal protection, input voltage range from output
voltage + 2V to 24V, 7805 voltage regulator IC form this series for 5V
output is very useful for
- LM79xx
series voltage regulators for negative voltages - practically same
specifications as 78xx series but for negative voltages (7905=-5V, 7908=-8V,
7912=-12V, 7915=-15V, 7818=-18V)
- L200
CH adjustable voltage and current regulator IC 2.9-36V, adjustable
overcurrent protection, PENTAWATT case, check
- LM
317 three pin variable voltage regulator for 1.2V to 37V and up to 1.5A
current
Interfacing ICs
- MAX232
- a very useful and easy to use RS-232 transmitter and receiver using
single +5V power supply from
- MAX220-MAX249
family of line drivers/receivers - intended for all EIA/TIA-232E and
V.28/V.24 communications interfaces, particularly applications where �12V
is not available.
- ULN2803
- 8-bit 50V 500mA TTL compatible input NPN darlington driver. This
driver is suitable for loads like lamps, relays printer hammers or other
similar loads for a broad range of computer, industrial, and consumer
applications. This device featurs open-collector outputs and free wheeling
clamp diodes for transient suppression. The ULN2803 is designed to be
compatible with standard TTL families.
- ULN2804
- 8-bit 50V 500mA CMOS/PMOS compatible input NPN darlington driver. This
driver is suitable for loads like lamps, relays printer hammers or other
similar loads for a broad range of computer, industrial, and consumer
applications. This device featurs open-collector outputs and free wheeling
clamp diodes for transient suppression. The ULN2804 is optimized for 6 to 15
volt high level CMOS or PMOS.
Optoisolators
- 4N25
optoisolator, CTR=20% (CTR=current transfer ratio), check
-
4N37
optoisolator, CTR=100%
- 6N138
optoisolater with split Darlington output, Vcc = 18 V max., 8 pin DIP,
check
Rate this link
- 6N138
optoisolater with split Darlington output, Vcc = 18 V max., 8 pin DIP
- CNY17
optoisolator, CTR for CNY17-3 is 100%, check
- MOC3023
optodiac
back to :
Links >>
Integrated circuits
|